TT30CDGP / TT30000M / TT2-30C
MAINTENANCE SCHEDULE

Regulator/Hose Assembly:
Check for Damage Before Every Use, Replace if Needed
Inspect all connections for leaks using 50/50 water/soap before every use
  • Burner Assembly: Inspect Screen and Rivets Weekly During the Season
    DO NOT USE in Areas With Extreme Amounts of Dust as Many Types are Comubstible
  • Nozzle/Mixing Tube: Remove Dirt/Debris Every Season
*
The above information is a baseline to follow. Please be advised that usage and/or environment may result in more frequent maintenance procedures. It is recommended to have the heater checked once a year by a qualified technician.
TECHNICAL INFORMATION

MAX REGULATOR INPUT PRESSURE
  • Bottle Pressure (This unit is for use with 20 lb propane tanks ONLY)
IGNITOR ELECTRODE GAP (PIEZO UNITS ONLY)
  • .15" (4mm) from thermocouple shield
MINIMUM COMBUSTIBLE CLEARANCES
  • TOP: 36" (91cm)
  • SIDE/REAR: 36" (91cm)
  • FRONT: 60" (150cm)
MINIMUM OPERATING TIME (HIGH SETTING)
  • 14 Hours
WIRING
DIAGRAM
 INSTRUCTION
MANUAL

ORDER PARTS COMING SOON!
CONTACT US:

CALL
EMAIL
WARRANTY:

WARRANTY
(Viewable PDF)
REGISTER PRODUCT
FIND REPAIR CENTER:

TROUBLESHOOTING *Always be sure your heater is turned off, unplugged and cool to the touch before continuing
 with troubleshooting.

NOTE: The regulator fitting (POL) that attaches to the propane tank is a left hand thread and needs to be turned counter-clockwise to attach and tighten.

Does the heater ignite (burner warms up and begins to glow red)?
Does the burner go out after the red valve plunger is released?
NOTE: The regulator fitting (POL) that attaches to the propane tank is a left hand thread and needs to be turned counter-clockwise to attach and tighten.

Please choose one of the following:

  1. Verify tilt switch is properly positioned and secured. The bottom edge of rectangle must be parallel to the floor.
  2. Loose wire connection or damaged tilt switch (refer to WIRING DIAGRAM in TECHNICAL INFORMATION), replace if necessary (ORDER PARTS).
  3. Loose or damaged thermocouple or wire (refer to WIRING DIAGRAM in TECHNICAL INFORMATION), replace if necessary (ORDER PARTS).
  4. Defective valve assembly. Replace if necessary (ORDER PARTS).
  1. Verify all supply connetions are secure and the propane tank has fuel and the valve is completely open.
  2. The propane tank's check valve may have actuated. Completely close propane tank valve and SLOWLY re-open.
  3. Be sure you are manually feeding fuel by holding the red plunger all the way in while attempting to light the burner and that the regulator is set to "HIGH" (refer to INSTRUCTION MANUAL inside TECHNICAL INFORMATION)
  4. The regulator or safety valve is defective, replace if necessary (ORDER PARTS).
  1. A burner rivet may be damaged. Replace burner if necessary (ORDER PARTS).
  2. Excessive dust or debris in mixing tube is disrupting fuel supply. Clean using pipe cleaner or bottle brush.
  3. Clogged or damaged orifice is disrupting the fuel supply. Remove and blow out using compressed air or rinse and dry thouroughly before reinstalling. Replace if needed (ORDER PARTS).
  1. Excessive dust or debris in mixing tube is disrupting fuel supply. Clean using pipe cleaner or bottle brush.
  2. Clogged or damaged orifice is disrupting the fuel supply. Remove and blow out using compressed air or rinse and dry thouroughly before reinstalling. Replace if needed (ORDER PARTS).
  1. Electrode is too far from or touching thermocouple shield. Regap to .15" (4mm).
  2. Piezo ignitor, wire is damaged or defective (refer to INSTRUCTION MANUAL for match lighting instructions). Replace if necessary (ORDER PARTS).